The visual positioning dispensing control system controls every step of the automatic visual positioning dispensing machine. As an automatic equipment, the automatic visual positioning dispensing machine is efficient and easy to operate, can replace the current shortage of artificial characteristics, can be widely used in many factories, then the impact of automatic visual positioning dispensing machine dispensing process what factors?

1, dispensing time, the longer the amount of glue will be greater, the opposite will be smaller. For the non-quantitative requirements, the size of the glue point diameter of the product is half of the diameter, you can ensure that sufficient glue to bond components and avoid glue waste.

2, glue viscosity, the higher the viscosity, the worse its fluidity, dispensing machine required to adjust the pressure will be greater.

3, if the glue bubble more, the need for vacuum treatment of the glue, and then use the dispenser point, in order to ensure the quality of dispensing products.

4, according to the dispensing process requirements and the nature of the glue to reasonable selection, is the dispensing valve or syringe, if the requirements are high, the glue is relatively thin, choose dispensing valve than syringe, the valve suction effect, to ensure no leakage of glue, for the more sticky glue, the advantages of dispensing valve than the needle barrel is high, can solve the wire drawing phenomenon. For glue viscosity moderate requirements of the product is not high, the choice of syringes on the line relatively low cost and can achieve dispensing requirements.

5, in strict accordance with the glue manufacturers given the temperature curve, the product after the point of curing.

6, reasonable selection of needle, needle diameter is half of the diameter of the glue point the best effect, for more corrosive glue, to choose Teflon needle, if it is UV glue glue, select a UV light shielding effect of the syringe and needle.

The visual positioning dispensing control system controls every step of the automatic visual positioning dispensing machine. As an automatic equipment, the automatic visual positioning dispensing machine is efficient and easy to operate, can replace the current shortage of artificial characteristics, can be widely used in many factories, then the impact of automatic visual positioning dispensing machine dispensing process what factors?

1, dispensing time, the longer the amount of glue will be greater, the opposite will be smaller. For the non-quantitative requirements, the size of the glue point diameter of the product is half of the diameter, you can ensure that sufficient glue to bond components and avoid glue waste.

2, glue viscosity, the higher the viscosity, the worse its fluidity, dispensing machine required to adjust the pressure will be greater.

3, if the glue bubble more, the need for vacuum treatment of the glue, and then use the dispenser point, in order to ensure the quality of dispensing products.

4, according to the dispensing process requirements and the nature of the glue to reasonable selection, is the dispensing valve or syringe, if the requirements are high, the glue is relatively thin, choose dispensing valve than syringe, the valve suction effect, to ensure no leakage of glue, for the more sticky glue, the advantages of dispensing valve than the needle barrel is high, can solve the wire drawing phenomenon. For glue viscosity moderate requirements of the product is not high, the choice of syringes on the line relatively low cost and can achieve dispensing requirements.

5, in strict accordance with the glue manufacturers given the temperature curve, the product after the point of curing.

6, reasonable selection of needle, needle diameter is half of the diameter of the glue point the best effect, for more corrosive glue, to choose Teflon needle, if it is UV glue glue, select a UV light shielding effect of the syringe and needle.

Automatic visual positioning dispenser equipment is widely used in various fields, such as semiconductors, electronic components and so on. Coincidentally, these areas of the automatic visual positioning dispenser production process requirements are very high, then how to effectively protect the automatic visual positioning dispenser accuracy? Today to tell you about how to protect the automatic visual positioning dispensing machine dispensing accuracy.

Dispensing size and glue viscosity settings:

The dispensing amount should be half of the product spacing in general, so that the component has enough glue for bonding, there will be no excess glue overflow, so that the automatic dispensing machine dispensing faster and more accurate. Glue viscosity, glue dot small, easy to wire drawing phenomenon, glue viscosity small, glue dot big, may appear glue dyeing product phenomenon, so the automatic dispensing machine to choose the appropriate glue viscosity is very important.

Dispensing needle and dispensing pressure settings: automatic visual positioning dispensing machine needle selection should be based on the size of the product and the diameter of the dispensing point to choose, usually, automatic visual positioning dispensing machine dispensing needle size should be half the size of the dispensing point, dispensing machine needle size is too large will cause glue overflow, affect dispensing accuracy. But the dispensing pressure is too big to cause the phenomenon of glue overflow, and the pressure is too small to cause leakage or intermittent dispensing, so the dispensing process can not meet the requirements of the product, making the product qualified rate low, low efficiency of work.

Dispensing machine needle and the working surface of the space between the settings: different automatic visual positioning dispensing machine used by the dispensing needle is also different, some needles have a certain degree of stop, some needles do not, therefore, it is very important to control the dispensing interval between the needle and the working face. The interval between the needle and the working face should be calibrated before dispensing.

The above is the visual positioning dispensing control system: how to control dispensing machine dispensing quality? I hope I can help you, and want to know more about the position of the dispensing control system information, you can pay attention to the NIHIRO intelligence update.

Automatic visual positioning dispenser equipment is widely used in various fields, such as semiconductors, electronic components and so on. Coincidentally, these areas of the automatic visual positioning dispenser production process requirements are very high, then how to effectively protect the automatic visual positioning dispenser accuracy? Today to tell you about how to protect the automatic visual positioning dispensing machine dispensing accuracy.

Dispensing size and glue viscosity settings:

The dispensing amount should be half of the product spacing in general, so that the component has enough glue for bonding, there will be no excess glue overflow, so that the automatic dispensing machine dispensing faster and more accurate. Glue viscosity, glue dot small, easy to wire drawing phenomenon, glue viscosity small, glue dot big, may appear glue dyeing product phenomenon, so the automatic dispensing machine to choose the appropriate glue viscosity is very important.

Dispensing needle and dispensing pressure settings: automatic visual positioning dispensing machine needle selection should be based on the size of the product and the diameter of the dispensing point to choose, usually, automatic visual positioning dispensing machine dispensing needle size should be half the size of the dispensing point, dispensing machine needle size is too large will cause glue overflow, affect dispensing accuracy. But the dispensing pressure is too big to cause the phenomenon of glue overflow, and the pressure is too small to cause leakage or intermittent dispensing, so the dispensing process can not meet the requirements of the product, making the product qualified rate low, low efficiency of work.

Dispensing machine needle and the working surface of the space between the settings: different automatic visual positioning dispensing machine used by the dispensing needle is also different, some needles have a certain degree of stop, some needles do not, therefore, it is very important to control the dispensing interval between the needle and the working face. The interval between the needle and the working face should be calibrated before dispensing.

The above is the visual positioning dispensing control system: how to control dispensing machine dispensing quality? I hope I can help you, and want to know more about the position of the dispensing control system information, you can pay attention to the NIHIRO intelligence update.

Disclaimer: This article is from the Tencent News client creator and does not represent the views and positions of Tencent